\ndownload firmware here\u00a0[Firmware 1.1 Download<\/a>]
\nmanual: [Manual Download<\/a>\u00a0v1.1]
\nNew features:<\/em><\/p>\n
- \n
- queued toggling (sync also for single channels)<\/li>\n
- MIDI converter disable for gate generation with the mute buttons<\/li>\n
- group recall<\/li>\n<\/ul>\n
old manual: [Manual Download<\/a>\u00a0v1.0]<\/p>\n
8 channel mute for audio, gate\/trigger and CV with toggle buttons and a grouping feature.<\/h6>\n
![\"\"](\"http:\/\/leipzigwest.org\/wp-content\/uploads\/2018\/04\/SCHLEU\u00dfIG_Panel-118x300.jpg\")
<\/a>Created for trigger mutes in performance setups with drum modules etc. but there is no reason not to mute the gate of a synth voice, the clock to a sequencer, the audio output of a device or the send path to an effect.<\/p>\nsynchronous toggle feature
\n<\/strong> Toggle multiple channels at the same time (mute on or off) either on the release of the “Group” button or when in “sync mode<\/strong>” at fixed point of the beat. The sync moment can be chosen while holding the sync button.
\nThe sync selection is:<\/p>\n- \n
- quarter note (a.k.a. always start with the kick after the break)<\/li>\n
- half note (a.k.a. never start with clap on 2)<\/li>\n
- bar (a.k.a. get the rest in line too)<\/li>\n
- 2 bars<\/li>\n
- 4 bars (a.k.a. free both hands to modulate something else in the break)<\/li>\n
- 8 bars (a.k.a. go and get your beer until something happens)<\/li>\n<\/ul>\n
Special Group-Hold mode<\/h6>\n
when activated will separate the “group” selection from the toggling so you can prepare first and later only need to press group again to do the mute\/unmute action.<\/p>\n
Sync information is derived from the MIDI input or DIN-SYNC (switch on the backside of the module).<\/p>\n
The MIDI input is 3.5mm stereo TRS, with our own invented auto-crossover (directly connect either Korg-like OR Arturial-like 3.5mm MIDI out with a cheap standard cable).<\/p>\n
Built-In MIDI to Trigger\/Gate converter: If you do not plug in a signal to the trigger input you can use the internal trigger converter.
\nThere is a MIDI learn mode you can access during startup, so you can assign notes to the 8 channels.<\/p>\nMultiple modules can be linked inside the rack so “group” and “sync” buttons only need to be pushed on one module.<\/p>\n
Expanders:<\/strong><\/h6>\n
- \n
- Alternate input expander in 2HP, switch A\/B instead of muting<\/li>\n
- Foot switch input
![\"\"](\"http:\/\/leipzigwest.org\/wp-content\/uploads\/2018\/04\/CV-Expander-23x300.jpg\")
<\/a>![\"\"](\"http:\/\/leipzigwest.org\/wp-content\/uploads\/2018\/04\/Alt-IN-Expander-23x300.jpg\")
<\/a>\u00a0(planed Q3 2018)<\/li>\n- Analog CV out expander 2HP (generated from MIDI note velocity data)<\/li>\n<\/ul>\n","protected":false},"excerpt":{"rendered":"
DC coupled mute\/switch with synchronous grouped switching New firmware out! download firmware here\u00a0[Firmware 1.1 Download] manual: [Manual Download\u00a0v1.1] New features: queued toggling (sync also for single channels) MIDI converter disable for gate generation with the mute buttons group recall old manual: [Manual Download\u00a0v1.0] 8 channel mute for audio, gate\/trigger and CV with toggle buttons and … <\/p>\n
- Analog CV out expander 2HP (generated from MIDI note velocity data)<\/li>\n<\/ul>\n","protected":false},"excerpt":{"rendered":"